How is the metal laser cutting machine ventilated during operation? As a metal laser cutting machine manufacturer, let the editor take everyone to understand how the metal laser cutting machine is ventilated during operation!

1. Exhaust treatment: Customers can choose whether to configure exhaust equipment when purchasing a metal laser cutting machine. The general exhaust equipment is composed of four parts: a gas hood, an air duct, a purification system, and a fan. It mainly uses airflow to treat local exhaust gas, so that the local work site is not polluted by harmful substances and maintains a good air environment.

2. Comprehensive ventilation: This method is a relatively simple and convenient operation method. It uses accelerated air flow inside the working area to dilute harmful gases in the air. Generally, an axial flow fan is installed on the top of the studio to discharge internal exhaust gas. This method is a common method.

When operating the laser cutting machine, what operational matters need to be paid attention to? As a Shandong laser cutting machine manufacturer, let the editor take everyone to understand what matters need to be paid attention to when operating the laser cutting machine!

It is necessary to strictly abide by the safety operating procedures of the laser cutting machine. Start the laser strictly according to the laser startup procedure. The operator must be trained, familiar with the equipment structure and performance, and master the relevant knowledge of the operating system. Wear labor protection equipment as required, and wear protective glasses that meet the regulations near the laser beam. Before it is clear whether a certain material can be irradiated or heated by laser, do not process it to avoid the potential danger of smoke and steam. When the equipment is started, the operator shall not leave the post or ask someone to take care of it without authorization. If it is really necessary to leave, the machine should be shut down or the power switch should be turned off. Keep the fire extinguisher within easy reach.

Turn off the laser or shutter when not processing; do not place paper, cloth or other flammable materials near the unprotected laser beam. If an abnormality is found during the processing, the machine should be shut down immediately, and the fault should be eliminated in time or reported to the supervisor. Keep the laser, bed and surrounding area clean, orderly and free of oil. Workpieces, plates and waste materials should be stacked according to regulations. When using gas cylinders, avoid crushing welding wires to avoid leakage accidents. The use and transportation of gas cylinders should comply with gas cylinder monitoring regulations. It is forbidden to expose gas cylinders to the sun or near heat sources. When opening the bottle valve, the operator needs to stand on the side of the bottle mouth. High-voltage safety regulations must be followed during maintenance. Maintenance should be carri

How to solve the problem of large slits in fiber laser cutting equipment, how to solve the problem of large slits, as a fiber laser cutting machine manufacturer, let the editor take you to understand together!

1. Check whether there is a problem with the focal length, especially pay attention to the focal length change after cleaning the lens and replacing the new lens, and adjust the correct focal length value!

2. Check whether the lens is damaged or dirty, because this situation will cause the laser to scatter, causing the laser beam to become thicker, replace or clean the lens.

3. The laser tube is also a factor that cannot be ignored. Check the quality of the laser tube light spot. If there is a bright spot or the light spot is not round, hollow, etc., it is the laser tube support point, whether the direction is appropriate! The solution requires adjusting the support, rotating the direction, and replacing the laser tube.

When using fiber laser cutting machines, for the price differences, let the editor of the fiber laser cutting machine manufacturer take everyone to understand the reasons for the difference in prices of fiber laser cutting machines!

1. There are many fiber laser cutting machine manufacturers. With so many manufacturers, the competition is naturally fierce. Customers will not only look at one company when they come. The competition is not only the competition of price, but also the competition of quality. Therefore, the products produced in the laser cutting machine industry-intensive areas are of high quality and low price.

2. There are many fiber laser cutting machine manufacturers, and the level of specialization of various accessories and assembly is high. Some manufacturers only produce laser cutting machine power supplies, and some manufacturers only produce cutting machine spindles, etc. This is the so-called specialization. These specialized companies are the guarantee of the quality of fiber laser cutting machine manufacturers.

3. It is a fact that there are many fiber laser cutting machine manufacturers. Large manufacturers developed earlier, have complete after-sales service guarantees, and a large number of machines are in operation, so the quality is relatively reliable.

4. Customers pursue cost-effectiveness. For the same product and the same configuration, the cost of large manufacturers is naturally high, including management expenses, factory expenses, etc., while the various expenses of small manufacturers are very low. Because of the division of labor and cooperation in China's socialized large-scale production, the professional level of its products is not necessarily lower than that of large manufacturers, but in terms of product quality and after-sales service, the products and after-sales service of large manufacturers are still better than those of small manufacturers, so if funds permit, it is recommended to consider the products of large manufacturers.

5. With the maturity of the fib

What are the advantages of fiber laser cutting machine? As a fiber laser cutting machine manufacturer, let me take you to understand the advantages of fiber laser cutting machine!

1. The cutting slit is narrow, the precision is high, the roughness of the cutting slit is good, and no post-processing is required after cutting.

2. The laser processing system itself is a computer system that can be easily arranged and modified, suitable for personalized processing, especially for some sheet metal parts with complex contours, large batches and small batches, and short product life cycle. From the perspective of technology, economic cost and time, it is not cost-effective to manufacture molds, and laser cutting is particularly advantageous.

3. The energy density of laser processing is very high, the action time is short, the heat affected zone is small, the thermal deformation is small, and the thermal stress is small. In addition, the laser is a non-mechanical contact processing, and there is no mechanical stress on the workpiece, which is suitable for dense processing.

4. The high energy density of the laser is enough to melt any metal, especially suitable for processing some high hardness, high brittleness and high melting point

5. The processing cost is low. The one-time investment in equipment is expensive, but continuous, large-scale processing reduces the processing cost of each part.

6. Laser is non-contact processing, with small inertia and fast processing speed. It is time-saving and convenient with the CAD/CAM software programming of the CNC system, and the overall efficiency is very high.

7. The laser has a high degree of automation, can be fully enclosed for processing, has low noise, and greatly improves the working environment of the operator.

When the metal laser cutting machine is working, what are the requirements for ventilation settings? As a metal laser cutting machine manufacturer, let the editor take everyone to understand the requirements for ventilation devices during the operation of metal laser cutting machines!

1. Exhaust treatment. Customers can choose whether to configure exhaust equipment when purchasing a metal laser cutting machine. The general exhaust equipment is composed of four parts: a gas hood, an air duct, a purification system, and a fan. It mainly uses airflow to treat local exhaust gas, so that the local work site is not polluted by harmful substances and maintains a good air environment.

2. Comprehensive ventilation. This method is a relatively simple and convenient operation method. It uses accelerated air flow inside the working area to dilute harmful gases in the air. Generally, an axial flow fan is installed on the top of the studio to discharge internal exhaust gas. This method is a common method.